NOTICE: CPU: STM32MP157AAA Rev.B NOTICE: Model: STMicroelectronics custom STM32CubeMX board - openstlinux-6.1-yocto-mickledore-mp1-v23.06.21 WARNING: VDD unknown INFO: Reset reason (0x14): INFO: Pad Reset from NRST INFO: FCONF: Reading TB_FW firmware configuration file from: 0x2ffe2000 INFO: FCONF: Reading firmware configuration information for: stm32mp_io INFO: Using SDMMC INFO: Instance 1 INFO: Boot used partition fsbl1 NOTICE: BL2: v2.8-stm32mp1-r1.0(debug):() NOTICE: BL2: Built : 13:19:21, Oct 13 2023 INFO: BL2: Doing platform setup INFO: RAM: DDR3-DDR3L 16bits 533000kHz INFO: Memory size = 0x20000000 (512 MB) INFO: BL2: Loading image id 1 INFO: Loading image id=1 at address 0x2ffff000 INFO: Image id=1 loaded: 0x2ffff000 - 0x2ffff1ea INFO: FCONF: Reading FW_CONFIG firmware configuration file from: 0x2ffff000 INFO: FCONF: Reading firmware configuration information for: dyn_cfg INFO: FCONF: Reading firmware configuration information for: stm32mp1_firewall INFO: BL2: Loading image id 4 INFO: Loading image id=4 at address 0x2ffc0000 INFO: Image id=4 loaded: 0x2ffc0000 - 0x2ffc002c INFO: OPTEE ep=0x2ffc0000 INFO: OPTEE header info: INFO: magic=0x4554504f INFO: version=0x2 INFO: arch=0x0 INFO: flags=0x0 INFO: nb_images=0x2 INFO: BL2: Loading image id 8 INFO: Loading image id=8 at address 0x2ffc0000 INFO: Image id=8 loaded: 0x2ffc0000 - 0x2ffd2768 INFO: BL2: Loading image id 9 INFO: Loading image id=9 at address 0xde000000 INFO: Image id=9 loaded: 0xde000000 - 0xde054000 INFO: BL2: Loading image id 2 INFO: Loading image id=2 at address 0xc0500000 INFO: Image id=2 loaded: 0xc0500000 - 0xc0511420 INFO: BL2: Skip loading image id 16 INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0xc0100000 INFO: Image id=5 loaded: 0xc0100000 - 0xc01d57b4 NOTICE: BL2: Booting BL32 INFO: Entry point address = 0x2ffc0000 INFO: SPSR = 0x1d3 I/TC: Early console on UART#4 I/TC: I/TC: Pager is enabled. Hashes: 2784 bytes I/TC: Pager pool size: 96kB I/TC: Embedded DTB found I/TC: OP-TEE version: Unknown_3.19 (gcc version 12.2.0 (GCC)) #1 Fri Oct 13 13:20:40 UTC 2023 arm I/TC: WARNING: This OP-TEE configuration might be insecure! I/TC: WARNING: Please check https://optee.readthedocs.io/en/latest/architecture/porting_guidelines.html I/TC: Primary CPU initializing I/TC: Platform stm32mp1: flavor PLATFORM_FLAVOR - DT stm32mp157a-board-mx.dts I/TC: DTB enables console (non-secure) I/TC: HUK unlocked I/TC: No power configuration found in DT I/TC: Primary CPU switching to normal world boot U-Boot 2022.10-stm32mp-r1 (Oct 13 2023 - 21:20:59 +0800) CPU: STM32MP157AAA Rev.B Model: STMicroelectronics custom STM32CubeMX board - openstlinux-6.1-yocto-mickledore-mp1-v23.06.21 DRAM: 512 MiB Core: 76 devices, 31 uclasses, devicetree: board NAND: 0 MiB MMC: STM32 SD/MMC: 0, STM32 SD/MMC: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Net: Hit any key to stop autoboot: 0 Boot over mmc0! switch to partitions #0, OK mmc0 is current device Scanning mmc 0:8... Found /mmc0_extlinux/extlinux.conf Retrieving file: /mmc0_extlinux/extlinux.conf Retrieving file: /splash_landscape.bmp 1: OpenSTLinux-Board v1 Enter choice: 1: OpenSTLinux-Board v1 Retrieving file: /uImage Retrieving file: /st-image-resize-initrd append: root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw earlyprintk console=ttySTM0,115200 loglevel=7 Retrieving file: /stm32mp157a-board-mx.dtb ## Booting kernel from Legacy Image at c2000000 ... Image Name: Linux-6.1.28 Created: 2023-10-12 6:45:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 10408448 Bytes = 9.9 MiB Load Address: c2000040 Entry Point: c2000040 Verifying Checksum ... OK ## Flattened Device Tree blob at c4000000 Booting using the fdt blob at 0xc4000000 XIP Kernel Image Loading Ramdisk to cfa0c000, end cffffcd7 ... OK Loading Device Tree to cf9fc000, end cfa0bddb ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.28 (user@H3) (arm-ostl-linux-gnueabi-gcc (GCC) 12.2.0, GNU ld (GNU Binutils) 2.40.20230119) #3 SMP Thu Oct 12 14:45:41 CST 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: STMicroelectronics custom STM32CubeMX board - openstlinux-6.1-yocto-mickledore-mp1-v23.06.21 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xd9000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00000000c0000000-0x00000000dcffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000dd000000-0x00000000dfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000c0000000-0x00000000dcffffff] [ 0.000000] node 0: [mem 0x00000000dd000000-0x00000000dfffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000c0000000-0x00000000dfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130144 [ 0.000000] Kernel command line: root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw earlyprintk console=ttySTM0,115200 loglevel=7 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 371016K/524288K available (15360K kernel code, 2484K rwdata, 6012K rodata, 2048K init, 429K bss, 87736K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 64.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0x1ffffffffffffff max_cycles: 0xec2a6fa00, max_idle_ns: 440795202120 ns [ 0.000002] sched_clock: 57 bits at 64MHz, resolution 15ns, wraps every 2199023255546ns [ 0.008057] Switching to timer-based delay loop, resolution 15ns [ 0.023867] Console: colour dummy device 80x30 [ 0.028425] Calibrating delay loop (skipped), value calculated using timer frequency.. 128.00 BogoMIPS (lpj=640000) [ 0.038960] pid_max: default: 32768 minimum: 301 [ 0.043854] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051249] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059938] CPU: Testing write buffer coherency: ok [ 0.065430] /cpus/cpu@0 missing clock-frequency property [ 0.070819] /cpus/cpu@1 missing clock-frequency property [ 0.076220] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.083119] Setting up static identity map for 0xc0300000 - 0xc03000ac [ 0.092365] rcu: Hierarchical SRCU implementation. [ 0.097200] rcu: Max phase no-delay instances is 1000. [ 0.108382] EFI services will not be available. [ 0.113444] smp: Bringing up secondary CPUs ... I/TC: Secondary CI/TC: Secondary CPU 1 switching to normal world boot [ 0.125378] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.125586] smp: Brought up 1 node, 2 CPUs [ 0.135441] SMP: Total of 2 processors activated (256.00 BogoMIPS). [ 0.141746] CPU: All CPU(s) started in SVC mode. [ 0.147318] devtmpfs: initialized [ 0.165383] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.173516] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.183482] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.193725] pinctrl core: initialized pinctrl subsystem [ 0.204428] DMI not present or invalid. [ 0.209609] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.218429] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.229917] thermal_sys: Registered thermal governor 'step_wise' [ 0.230071] cpuidle: using governor menu [ 0.240548] No ATAGs? [ 0.242975] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.251078] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.261641] Serial: AMBA PL011 UART driver [ 0.270203] stm32-pm-domain pm_domain: domain core-ret-power-domain registered [ 0.277562] stm32-pm-domain pm_domain: subdomain core-power-domain registered [ 0.284741] stm32-pm-domain pm_domain: domains probed [ 0.340645] iommu: Default domain type: Translated [ 0.345571] iommu: DMA domain TLB invalidation policy: strict mode [ 0.352968] SCSI subsystem initialized [ 0.357713] usbcore: registered new interface driver usbfs [ 0.363434] usbcore: registered new interface driver hub [ 0.368842] usbcore: registered new device driver usb [ 0.375587] pps_core: LinuxPPS API ver. 1 registered [ 0.380591] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.389854] PTP clock support registered [ 0.394060] EDAC MC: Ver: 3.0.0 [ 0.401790] vgaarb: loaded [ 1.938775] clocksource: Switched to clocksource arch_sys_counter [ 1.962854] NET: Registered PF_INET protocol family [ 1.968228] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.977899] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.986511] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.994493] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 2.002438] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 2.009839] TCP: Hash tables configured (established 4096 bind 4096) [ 2.016391] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 2.023064] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 2.030413] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.037212] RPC: Registered named UNIX socket transport module. [ 2.043263] RPC: Registered udp transport module. [ 2.047995] RPC: Registered tcp transport module. [ 2.052757] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.059269] PCI: CLS 0 bytes, default 64 [ 2.063873] Trying to unpack rootfs image as initramfs... [ 2.071014] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 2.081236] Initialise system trusted keyrings [ 2.086262] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 2.102313] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.109668] NFS: Registering the id_resolver key type [ 2.114919] Key type id_resolver registered [ 2.119233] Key type id_legacy registered [ 2.123551] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.130415] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.137948] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.143658] Key type asymmetric registered [ 2.147815] Asymmetric key parser 'x509' registered [ 2.153110] bounce: pool size: 64 pages [ 2.157212] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.164789] io scheduler mq-deadline registered [ 2.169394] io scheduler kyber registered [ 2.314270] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.326650] SuperH (H)SCI(F) driver initialized [ 2.332650] msm_serial: driver initialized [ 2.336792] STMicroelectronics ASC driver initialized [ 2.343983] STM32 USART driver initialized [ 2.375099] brd: module loaded [ 2.388818] loop: module loaded [ 2.408882] CAN device driver interface [ 2.414287] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.421587] e1000e: Intel(R) PRO/1000 Network Driver [ 2.426603] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.432832] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.438280] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.450017] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 2.455769] usbcore: registered new interface driver pegasus [ 2.461626] usbcore: registered new interface driver asix [ 2.467221] usbcore: registered new interface driver ax88179_178a [ 2.473519] usbcore: registered new interface driver cdc_ether [ 2.479606] usbcore: registered new interface driver smsc75xx [ 2.485511] usbcore: registered new interface driver smsc95xx [ 2.491493] usbcore: registered new interface driver net1080 [ 2.497278] usbcore: registered new interface driver cdc_subset [ 2.503409] usbcore: registered new interface driver zaurus [ 2.509243] usbcore: registered new interface driver cdc_ncm [ 2.521377] usbcore: registered new interface driver usb-storage [ 2.535227] i2c_dev: i2c /dev entries driver [ 2.564335] sdhci: Secure Digital Host Controller Interface driver [ 2.570626] sdhci: Copyright(c) Pierre Ossman [ 2.577981] Synopsys Designware Multimedia Card Interface Driver [ 2.586768] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.597705] ledtrig-cpu: registered to indicate activity on CPUs [ 2.607026] usbcore: registered new interface driver usbhid [ 2.612743] usbhid: USB HID core driver [ 2.628211] NET: Registered PF_INET6 protocol family [ 2.635541] Segment Routing with IPv6 [ 2.639523] In-situ OAM (IOAM) with IPv6 [ 2.643649] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.650880] NET: Registered PF_PACKET protocol family [ 2.655995] can: controller area network core [ 2.660544] NET: Registered PF_CAN protocol family [ 2.665396] can: raw protocol [ 2.668398] can: broadcast manager protocol [ 2.672658] can: netlink gateway - max_hops=1 [ 2.675984] Freeing initrd memory: 6096K [ 2.677688] Key type dns_resolver registered [ 2.685529] ThumbEE CPU extension supported. [ 2.689871] Registering SWP/SWPB emulation handler [ 2.695672] Loading compiled-in X.509 certificates [ 2.756089] Warning: unable to open an initial console. [ 2.765557] Freeing unused kernel image (initmem) memory: 2048K [ 2.809249] Run /init as init process [ 13.394599] platform 50000000.rcc: deferred probe pending [ 13.400134] platform 5000d000.interrupt-controller: deferred probe pending [ 13.407063] platform 48002000.dma-router: deferred probe pending [ 13.413187] platform soc:pinctrl@50002000: deferred probe pending [ 13.419346] platform soc:pinctrl@54004000: deferred probe pending [ 13.425474] platform 48000000.dma-controller: deferred probe pending [ 13.431881] platform 58000000.dma-controller: deferred probe pending [ 13.438271] platform 5a006000.usbphyc: deferred probe pending [ 13.444066] platform 50001000.pwr: deferred probe pending [ 13.449524] platform 5800c000.usb: deferred probe pending [ 13.454956] platform 40010000.serial: deferred probe pending [ 13.460698] platform 49000000.usb-otg: deferred probe pending [ 13.466480] platform 5c004000.rtc: deferred probe pending [ 13.471937] platform stm32-cpufreq: deferred probe pending [ 13.477455] amba 58005000.mmc: deferred probe pending [ 13.482549] amba 58007000.mmc: deferred probe pending [ 13.487629] platform leds: deferred probe pending