/dts-v1/;

/ {
	#address-cells = <0x1>;
	#size-cells = <0x1>;
	model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
	compatible = "st,stm32mp157a-dk1", "st,stm32mp157";

	cpus {
		#address-cells = <0x1>;
		#size-cells = <0x0>;

		cpu@0 {
			compatible = "arm,cortex-a7";
			clock-frequency = <0x26be3680>;
			device_type = "cpu";
			reg = <0x0>;
		};

		cpu@1 {
			compatible = "arm,cortex-a7";
			clock-frequency = <0x26be3680>;
			device_type = "cpu";
			reg = <0x1>;
		};
	};

	psci {
		compatible = "arm,psci";
		method = "smc";
		cpu_off = <0x84000002>;
		cpu_on = <0x84000003>;
	};

	interrupt-controller@a0021000 {
		compatible = "arm,cortex-a7-gic";
		#interrupt-cells = <0x3>;
		interrupt-controller;
		reg = <0xa0021000 0x1000 0xa0022000 0x2000>;
		phandle = <0x1>;
	};

	timer {
		compatible = "arm,armv7-timer";
		interrupts = <0x1 0xd 0xf08 0x1 0xe 0xf08 0x1 0xb 0xf08 0x1 0xa 0xf08>;
		interrupt-parent = <0x1>;
	};

	clocks {

		clk-hse {
			#clock-cells = <0x0>;
			compatible = "fixed-clock";
			clock-frequency = <0x16e3600>;
			phandle = <0x51>;
		};

		clk-hsi {
			#clock-cells = <0x0>;
			compatible = "fixed-clock";
			clock-frequency = <0x3d09000>;
		};

		clk-lse {
			#clock-cells = <0x0>;
			compatible = "fixed-clock";
			clock-frequency = <0x8000>;
			phandle = <0x21>;
		};

		clk-lsi {
			#clock-cells = <0x0>;
			compatible = "fixed-clock";
			clock-frequency = <0x7d00>;
		};

		clk-csi {
			#clock-cells = <0x0>;
			compatible = "fixed-clock";
			clock-frequency = <0x3d0900>;
		};
	};

	thermal-zones {

		cpu-thermal {
			polling-delay-passive = <0x0>;
			polling-delay = <0x0>;
			thermal-sensors = <0x2>;

			trips {

				cpu-alert1 {
					temperature = <0x14c08>;
					hysteresis = <0x0>;
					type = "passive";
				};

				cpu-crit {
					temperature = <0x1d4c0>;
					hysteresis = <0x0>;
					type = "critical";
				};
			};

			cooling-maps {
			};
		};
	};

	regulator-booster {
		compatible = "st,stm32mp1-booster";
		st,syscfg = <0x3>;
		status = "disabled";
	};

	soc {
		compatible = "simple-bus";
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		interrupt-parent = <0x1>;
		ranges;

		timer@40000000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40000000 0x400>;
			clocks = <0x4 0xc5>;
			clock-names = "int";
			dmas = <0x5 0x12 0x400 0x1 0x5 0x13 0x400 0x1 0x5 0x14 0x400 0x1 0x5 0x15 0x400 0x1 0x5 0x16 0x400 0x1>;
			dma-names = "ch1", "ch2", "ch3", "ch4", "up";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@1 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x1>;
				status = "disabled";
			};

			counter {
				compatible = "st,stm32-timer-counter";
				status = "disabled";
			};
		};

		timer@40001000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40001000 0x400>;
			clocks = <0x4 0xc6>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "okay";
				pinctrl-0 = <0x6>;
				pinctrl-1 = <0x7>;
				pinctrl-names = "default", "sleep";
			};

			timer@2 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x2>;
				status = "okay";
			};

			counter {
				compatible = "st,stm32-timer-counter";
				status = "disabled";
			};
		};

		timer@40002000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40002000 0x400>;
			clocks = <0x4 0xc7>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "okay";
				pinctrl-0 = <0x8 0x9>;
				pinctrl-1 = <0xa 0xb>;
				pinctrl-names = "default", "sleep";
			};

			timer@3 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x3>;
				status = "okay";
			};

			counter {
				compatible = "st,stm32-timer-counter";
				status = "disabled";
			};
		};

		timer@40003000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40003000 0x400>;
			clocks = <0x4 0xc8>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "okay";
				pinctrl-0 = <0xc>;
				pinctrl-1 = <0xd>;
				pinctrl-names = "default", "sleep";
			};

			timer@4 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x4>;
				status = "okay";
			};

			counter {
				compatible = "st,stm32-timer-counter";
				status = "disabled";
			};
		};

		timer@40004000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40004000 0x400>;
			clocks = <0x4 0xc9>;
			clock-names = "int";
			status = "disabled";

			timer@5 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x5>;
				status = "okay";
			};
		};

		timer@40005000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40005000 0x400>;
			clocks = <0x4 0xca>;
			clock-names = "int";
			dmas = <0x5 0x46 0x400 0x1>;
			dma-names = "up";
			status = "disabled";

			timer@6 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x6>;
				status = "disabled";
			};
		};

		timer@40006000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40006000 0x400>;
			clocks = <0x4 0xcb>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "okay";
				pinctrl-0 = <0xe>;
				pinctrl-1 = <0xf>;
				pinctrl-names = "default", "sleep";
			};

			timer@11 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0xb>;
				status = "okay";
			};
		};

		timer@40007000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40007000 0x400>;
			clocks = <0x4 0xcc>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@12 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0xc>;
				status = "disabled";
			};
		};

		timer@40008000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x40008000 0x400>;
			clocks = <0x4 0xcd>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@13 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0xd>;
				status = "disabled";
			};
		};

		timer@40009000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-lptimer";
			reg = <0x40009000 0x400>;
			clocks = <0x4 0x8f>;
			clock-names = "mux";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm-lp";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			trigger@0 {
				compatible = "st,stm32-lptimer-trigger";
				reg = <0x0>;
				status = "disabled";
			};

			counter {
				compatible = "st,stm32-lptimer-counter";
				status = "disabled";
			};
		};

		spi@4000b000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32h7-spi";
			reg = <0x4000b000 0x400>;
			interrupts = <0x0 0x24 0x4>;
			clocks = <0x4 0x83>;
			resets = <0x4 0x4c0b>;
			dmas = <0x5 0x27 0x400 0x5 0x5 0x28 0x400 0x5>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		audio-controller@4000b000 {
			compatible = "st,stm32h7-i2s";
			#sound-dai-cells = <0x0>;
			reg = <0x4000b000 0x400>;
			interrupts = <0x0 0x24 0x4>;
			dmas = <0x5 0x27 0x400 0x1 0x5 0x28 0x400 0x1>;
			dma-names = "rx", "tx";
			status = "okay";
			clocks = <0x4 0x10 0x4 0x83 0x4 0xbb 0x4 0xbc>;
			clock-names = "pclk", "i2sclk", "x8k", "x11k";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <0x10>;
			pinctrl-1 = <0x11>;

			port {
				phandle = <0x5c>;

				endpoint {
					remote-endpoint = <0x12>;
					format = "i2s";
					mclk-fs = <0x100>;
					phandle = <0x1b>;
				};
			};
		};

		spi@4000c000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32h7-spi";
			reg = <0x4000c000 0x400>;
			interrupts = <0x0 0x33 0x4>;
			clocks = <0x4 0x84>;
			resets = <0x4 0x4c0c>;
			dmas = <0x5 0x3d 0x400 0x5 0x5 0x3e 0x400 0x5>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		audio-controller@4000c000 {
			compatible = "st,stm32h7-i2s";
			#sound-dai-cells = <0x0>;
			reg = <0x4000c000 0x400>;
			interrupts = <0x0 0x33 0x4>;
			dmas = <0x5 0x3d 0x400 0x1 0x5 0x3e 0x400 0x1>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		audio-controller@4000d000 {
			compatible = "st,stm32h7-spdifrx";
			#sound-dai-cells = <0x0>;
			reg = <0x4000d000 0x400>;
			clocks = <0x4 0x81>;
			clock-names = "kclk";
			interrupts = <0x0 0x61 0x4>;
			dmas = <0x5 0x5d 0x400 0x1 0x5 0x5e 0x400 0x1>;
			dma-names = "rx", "rx-ctrl";
			status = "disabled";
		};

		serial@4000e000 {
			compatible = "st,stm32h7-uart";
			reg = <0x4000e000 0x400>;
			interrupts = <0x0 0x26 0x4>;
			clocks = <0x4 0x95>;
			status = "disabled";
		};

		serial@4000f000 {
			compatible = "st,stm32h7-uart";
			reg = <0x4000f000 0x400>;
			interrupts = <0x0 0x27 0x4>;
			clocks = <0x4 0x96>;
			status = "disabled";
		};

		serial@40010000 {
			compatible = "st,stm32h7-uart";
			reg = <0x40010000 0x400>;
			interrupts = <0x0 0x34 0x4>;
			clocks = <0x4 0x97>;
			status = "okay";
			pinctrl-names = "default";
			pinctrl-0 = <0x13>;
		};

		serial@40011000 {
			compatible = "st,stm32h7-uart";
			reg = <0x40011000 0x400>;
			interrupts = <0x0 0x35 0x4>;
			clocks = <0x4 0x98>;
			status = "disabled";
		};

		i2c@40012000 {
			compatible = "st,stm32f7-i2c";
			reg = <0x40012000 0x400>;
			interrupt-names = "event", "error";
			interrupts = <0x0 0x1f 0x4 0x0 0x20 0x4>;
			clocks = <0x4 0x89>;
			resets = <0x4 0x4c15>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			wakeup-source;
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <0x14>;
			pinctrl-1 = <0x15>;
			i2c-scl-rising-time-ns = <0x64>;
			i2c-scl-falling-time-ns = <0x7>;

			hdmi-transmitter@39 {
				compatible = "sil,sii9022";
				reg = <0x39>;
				iovcc-supply = <0x16>;
				cvcc12-supply = <0x17>;
				reset-gpios = <0x18 0xa 0x1>;
				interrupts = <0x1 0x2>;
				interrupt-parent = <0x19>;
				#sound-dai-cells = <0x0>;
				status = "okay";

				ports {
					#address-cells = <0x1>;
					#size-cells = <0x0>;

					port@0 {
						reg = <0x0>;

						endpoint {
							remote-endpoint = <0x1a>;
							phandle = <0x47>;
						};
					};

					port@3 {
						reg = <0x3>;

						endpoint {
							remote-endpoint = <0x1b>;
							phandle = <0x12>;
						};
					};
				};
			};

			cs42l51@4a {
				compatible = "cirrus,cs42l51";
				reg = <0x4a>;
				#sound-dai-cells = <0x0>;
				VL-supply = <0x1c>;
				VD-supply = <0x1d>;
				VA-supply = <0x1d>;
				VAHP-supply = <0x1d>;
				reset-gpios = <0x19 0x9 0x1>;
				clocks = <0x1e>;
				clock-names = "MCLK";
				status = "okay";

				port {
					#address-cells = <0x1>;
					#size-cells = <0x0>;

					endpoint@0 {
						reg = <0x0>;
						remote-endpoint = <0x1f>;
						frame-master;
						bitclock-master;
						phandle = <0x2a>;
					};

					endpoint@1 {
						reg = <0x1>;
						remote-endpoint = <0x20>;
						frame-master;
						bitclock-master;
						phandle = <0x2b>;
					};
				};
			};
		};

		i2c@40013000 {
			compatible = "st,stm32f7-i2c";
			reg = <0x40013000 0x400>;
			interrupt-names = "event", "error";
			interrupts = <0x0 0x21 0x4 0x0 0x22 0x4>;
			clocks = <0x4 0x8a>;
			resets = <0x4 0x4c16>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			wakeup-source;
			status = "disabled";
		};

		i2c@40014000 {
			compatible = "st,stm32f7-i2c";
			reg = <0x40014000 0x400>;
			interrupt-names = "event", "error";
			interrupts = <0x0 0x48 0x4 0x0 0x49 0x4>;
			clocks = <0x4 0x8b>;
			resets = <0x4 0x4c17>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			wakeup-source;
			status = "disabled";
		};

		i2c@40015000 {
			compatible = "st,stm32f7-i2c";
			reg = <0x40015000 0x400>;
			interrupt-names = "event", "error";
			interrupts = <0x0 0x6b 0x4 0x0 0x6c 0x4>;
			clocks = <0x4 0x8d>;
			resets = <0x4 0x4c18>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			wakeup-source;
			status = "disabled";
		};

		cec@40016000 {
			compatible = "st,stm32-cec";
			reg = <0x40016000 0x400>;
			interrupts = <0x0 0x5e 0x4>;
			clocks = <0x4 0x88 0x21>;
			clock-names = "cec", "hdmi-cec";
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <0x22>;
			pinctrl-1 = <0x23>;
		};

		dac@40017000 {
			compatible = "st,stm32h7-dac-core";
			reg = <0x40017000 0x400>;
			clocks = <0x4 0x1e>;
			clock-names = "pclk";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			status = "disabled";

			dac@1 {
				compatible = "st,stm32-dac";
				#io-channels-cells = <0x1>;
				reg = <0x1>;
				status = "disabled";
			};

			dac@2 {
				compatible = "st,stm32-dac";
				#io-channels-cells = <0x1>;
				reg = <0x2>;
				status = "disabled";
			};
		};

		serial@40018000 {
			compatible = "st,stm32h7-uart";
			reg = <0x40018000 0x400>;
			interrupts = <0x0 0x52 0x4>;
			clocks = <0x4 0x9a>;
			status = "disabled";
		};

		serial@40019000 {
			compatible = "st,stm32h7-uart";
			reg = <0x40019000 0x400>;
			interrupts = <0x0 0x53 0x4>;
			clocks = <0x4 0x9b>;
			status = "disabled";
		};

		timer@44000000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x44000000 0x400>;
			clocks = <0x4 0xce>;
			clock-names = "int";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "okay";
				pinctrl-0 = <0x24>;
				pinctrl-1 = <0x25>;
				pinctrl-names = "default", "sleep";
			};

			timer@0 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x0>;
				status = "okay";
			};

			counter {
				compatible = "st,stm32-timer-counter";
				status = "disabled";
			};
		};

		timer@44001000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x44001000 0x400>;
			clocks = <0x4 0xcf>;
			clock-names = "int";
			dmas = <0x5 0x2f 0x400 0x1 0x5 0x30 0x400 0x1 0x5 0x31 0x400 0x1 0x5 0x32 0x400 0x1 0x5 0x33 0x400 0x1 0x5 0x34 0x400 0x1 0x5 0x35 0x400 0x1>;
			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@7 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x7>;
				status = "disabled";
			};

			counter {
				compatible = "st,stm32-timer-counter";
				status = "disabled";
			};
		};

		serial@44003000 {
			compatible = "st,stm32h7-uart";
			reg = <0x44003000 0x400>;
			interrupts = <0x0 0x47 0x4>;
			clocks = <0x4 0x99>;
			status = "disabled";
		};

		spi@44004000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32h7-spi";
			reg = <0x44004000 0x400>;
			interrupts = <0x0 0x23 0x4>;
			clocks = <0x4 0x82>;
			resets = <0x4 0x4c48>;
			dmas = <0x5 0x25 0x400 0x5 0x5 0x26 0x400 0x5>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		audio-controller@44004000 {
			compatible = "st,stm32h7-i2s";
			#sound-dai-cells = <0x0>;
			reg = <0x44004000 0x400>;
			interrupts = <0x0 0x23 0x4>;
			dmas = <0x5 0x25 0x400 0x1 0x5 0x26 0x400 0x1>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		spi@44005000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32h7-spi";
			reg = <0x44005000 0x400>;
			interrupts = <0x0 0x54 0x4>;
			clocks = <0x4 0x85>;
			resets = <0x4 0x4c49>;
			dmas = <0x5 0x53 0x400 0x5 0x5 0x54 0x400 0x5>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		timer@44006000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x44006000 0x400>;
			clocks = <0x4 0xd0>;
			clock-names = "int";
			dmas = <0x5 0x69 0x400 0x1 0x5 0x6a 0x400 0x1 0x5 0x6b 0x400 0x1 0x5 0x6c 0x400 0x1>;
			dma-names = "ch1", "up", "trig", "com";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@14 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0xe>;
				status = "disabled";
			};
		};

		timer@44007000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x44007000 0x400>;
			clocks = <0x4 0xd1>;
			clock-names = "int";
			dmas = <0x5 0x6d 0x400 0x1 0x5 0x6e 0x400 0x1>;
			dma-names = "ch1", "up";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@15 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0xf>;
				status = "disabled";
			};
		};

		timer@44008000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-timers";
			reg = <0x44008000 0x400>;
			clocks = <0x4 0xd2>;
			clock-names = "int";
			dmas = <0x5 0x6f 0x400 0x1 0x5 0x70 0x400 0x1>;
			dma-names = "ch1", "up";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			timer@16 {
				compatible = "st,stm32h7-timer-trigger";
				reg = <0x10>;
				status = "disabled";
			};
		};

		spi@44009000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32h7-spi";
			reg = <0x44009000 0x400>;
			interrupts = <0x0 0x55 0x4>;
			clocks = <0x4 0x86>;
			resets = <0x4 0x4c4a>;
			dmas = <0x5 0x55 0x400 0x5 0x5 0x56 0x400 0x5>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		sai@4400a000 {
			compatible = "st,stm32h7-sai";
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			ranges = <0x0 0x4400a000 0x400>;
			reg = <0x4400a000 0x4 0x4400a3f0 0x10>;
			interrupts = <0x0 0x57 0x4>;
			resets = <0x4 0x4c50>;
			status = "disabled";

			audio-controller@4400a004 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-a";
				reg = <0x4 0x1c>;
				clocks = <0x4 0x9e>;
				clock-names = "sai_ck";
				dmas = <0x5 0x57 0x400 0x1>;
				status = "disabled";
			};

			audio-controller@4400a024 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-b";
				reg = <0x24 0x1c>;
				clocks = <0x4 0x9e>;
				clock-names = "sai_ck";
				dmas = <0x5 0x58 0x400 0x1>;
				status = "disabled";
			};
		};

		sai@4400b000 {
			compatible = "st,stm32h7-sai";
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			ranges = <0x0 0x4400b000 0x400>;
			reg = <0x4400b000 0x4 0x4400b3f0 0x10>;
			interrupts = <0x0 0x5b 0x4>;
			resets = <0x4 0x4c51>;
			status = "okay";
			clocks = <0x4 0x2a 0x4 0xbb 0x4 0xbc>;
			clock-names = "pclk", "x8k", "x11k";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <0x26 0x27>;
			pinctrl-1 = <0x28 0x29>;

			audio-controller@4400b004 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-a";
				reg = <0x4 0x1c>;
				clocks = <0x4 0x9f>;
				clock-names = "sai_ck";
				dmas = <0x5 0x59 0x400 0x1>;
				status = "okay";
				#clock-cells = <0x0>;
				dma-names = "tx";
				phandle = <0x1e>;

				port {
					phandle = <0x5a>;

					endpoint {
						remote-endpoint = <0x2a>;
						format = "i2s";
						mclk-fs = <0x100>;
						dai-tdm-slot-num = <0x2>;
						dai-tdm-slot-width = <0x20>;
						phandle = <0x1f>;
					};
				};
			};

			audio-controller@4400b024 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-b";
				reg = <0x24 0x1c>;
				clocks = <0x4 0x9f 0x1e>;
				clock-names = "sai_ck", "MCLK";
				dmas = <0x5 0x5a 0x400 0x1>;
				status = "okay";
				dma-names = "rx";
				st,sync = <0x1e 0x2>;

				port {
					phandle = <0x5b>;

					endpoint {
						remote-endpoint = <0x2b>;
						format = "i2s";
						mclk-fs = <0x100>;
						dai-tdm-slot-num = <0x2>;
						dai-tdm-slot-width = <0x20>;
						phandle = <0x20>;
					};
				};
			};
		};

		sai@4400c000 {
			compatible = "st,stm32h7-sai";
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			ranges = <0x0 0x4400c000 0x400>;
			reg = <0x4400c000 0x4 0x4400c3f0 0x10>;
			interrupts = <0x0 0x72 0x4>;
			resets = <0x4 0x4c52>;
			status = "disabled";

			audio-controller@4400c004 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-a";
				reg = <0x4 0x1c>;
				clocks = <0x4 0xa0>;
				clock-names = "sai_ck";
				dmas = <0x5 0x71 0x400 0x1>;
				status = "disabled";
			};

			audio-controller@4400c024 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-b";
				reg = <0x24 0x1c>;
				clocks = <0x4 0xa0>;
				clock-names = "sai_ck";
				dmas = <0x5 0x72 0x400 0x1>;
				status = "disabled";
			};
		};

		dfsdm@4400d000 {
			compatible = "st,stm32mp1-dfsdm";
			reg = <0x4400d000 0x800>;
			clocks = <0x4 0x9c>;
			clock-names = "dfsdm";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			status = "disabled";

			filter@0 {
				compatible = "st,stm32-dfsdm-adc";
				#io-channel-cells = <0x1>;
				reg = <0x0>;
				interrupts = <0x0 0x6e 0x4>;
				dmas = <0x5 0x65 0x400 0x1>;
				dma-names = "rx";
				status = "disabled";
			};

			filter@1 {
				compatible = "st,stm32-dfsdm-adc";
				#io-channel-cells = <0x1>;
				reg = <0x1>;
				interrupts = <0x0 0x6f 0x4>;
				dmas = <0x5 0x66 0x400 0x1>;
				dma-names = "rx";
				status = "disabled";
			};

			filter@2 {
				compatible = "st,stm32-dfsdm-adc";
				#io-channel-cells = <0x1>;
				reg = <0x2>;
				interrupts = <0x0 0x70 0x4>;
				dmas = <0x5 0x67 0x400 0x1>;
				dma-names = "rx";
				status = "disabled";
			};

			filter@3 {
				compatible = "st,stm32-dfsdm-adc";
				#io-channel-cells = <0x1>;
				reg = <0x3>;
				interrupts = <0x0 0x71 0x4>;
				dmas = <0x5 0x68 0x400 0x1>;
				dma-names = "rx";
				status = "disabled";
			};

			filter@4 {
				compatible = "st,stm32-dfsdm-adc";
				#io-channel-cells = <0x1>;
				reg = <0x4>;
				interrupts = <0x0 0x73 0x4>;
				dmas = <0x5 0x5b 0x400 0x1>;
				dma-names = "rx";
				status = "disabled";
			};

			filter@5 {
				compatible = "st,stm32-dfsdm-adc";
				#io-channel-cells = <0x1>;
				reg = <0x5>;
				interrupts = <0x0 0x7e 0x4>;
				dmas = <0x5 0x5c 0x400 0x1>;
				dma-names = "rx";
				status = "disabled";
			};
		};

		dma-controller@48000000 {
			compatible = "st,stm32-dma";
			reg = <0x48000000 0x400>;
			interrupts = <0x0 0xb 0x4 0x0 0xc 0x4 0x0 0xd 0x4 0x0 0xe 0x4 0x0 0xf 0x4 0x0 0x10 0x4 0x0 0x11 0x4 0x0 0x2f 0x4>;
			clocks = <0x4 0x47>;
			resets = <0x4 0x4cc0>;
			#dma-cells = <0x4>;
			st,mem2mem;
			dma-requests = <0x8>;
			phandle = <0x2c>;
		};

		dma-controller@48001000 {
			compatible = "st,stm32-dma";
			reg = <0x48001000 0x400>;
			interrupts = <0x0 0x38 0x4 0x0 0x39 0x4 0x0 0x3a 0x4 0x0 0x3b 0x4 0x0 0x3c 0x4 0x0 0x44 0x4 0x0 0x45 0x4 0x0 0x46 0x4>;
			clocks = <0x4 0x48>;
			resets = <0x4 0x4cc1>;
			#dma-cells = <0x4>;
			st,mem2mem;
			dma-requests = <0x8>;
			phandle = <0x2d>;
		};

		dma-router@48002000 {
			compatible = "st,stm32h7-dmamux";
			reg = <0x48002000 0x1c>;
			#dma-cells = <0x3>;
			dma-requests = <0x80>;
			dma-masters = <0x2c 0x2d>;
			dma-channels = <0x10>;
			clocks = <0x4 0x49>;
			resets = <0x4 0x4cc2>;
			phandle = <0x5>;
		};

		adc@48003000 {
			compatible = "st,stm32mp1-adc-core";
			reg = <0x48003000 0x400>;
			interrupts = <0x0 0x12 0x4 0x0 0x5a 0x4>;
			clocks = <0x4 0x4a 0x4 0xa2>;
			clock-names = "bus", "adc";
			interrupt-controller;
			st,syscfg = <0x3>;
			#interrupt-cells = <0x1>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			status = "disabled";
			pinctrl-names = "default";
			pinctrl-0 = <0x2e 0x2f>;
			vdd-supply = <0x30>;
			vdda-supply = <0x30>;
			vref-supply = <0x31>;
			phandle = <0x32>;

			adc@0 {
				compatible = "st,stm32mp1-adc";
				#io-channel-cells = <0x1>;
				reg = <0x0>;
				interrupt-parent = <0x32>;
				interrupts = <0x0>;
				dmas = <0x5 0x9 0x400 0x1>;
				dma-names = "rx";
				status = "okay";
				st,min-sample-time-nsecs = <0x1388>;
				st,adc-channels = <0x0 0x1 0x6 0xd 0x12 0x13>;
			};

			adc@100 {
				compatible = "st,stm32mp1-adc";
				#io-channel-cells = <0x1>;
				reg = <0x100>;
				interrupt-parent = <0x32>;
				interrupts = <0x1>;
				dmas = <0x5 0xa 0x400 0x1>;
				dma-names = "rx";
				status = "okay";
				st,adc-channels = <0x0 0x1 0x2 0x6 0x12 0x13>;
				st,min-sample-time-nsecs = <0x1388>;
			};
		};

		sdmmc@48004000 {
			compatible = "arm,pl18x", "arm,primecell";
			arm,primecell-periphid = <0x10153180>;
			reg = <0x48004000 0x400>;
			interrupts = <0x0 0x89 0x4>;
			interrupt-names = "cmd_irq";
			clocks = <0x4 0x78>;
			clock-names = "apb_pclk";
			resets = <0x4 0x4cd0>;
			cap-sd-highspeed;
			cap-mmc-highspeed;
			max-frequency = <0x7270e00>;
			status = "disabled";
			pinctrl-names = "default", "opendrain", "sleep";
			pinctrl-0 = <0x33>;
			pinctrl-1 = <0x34>;
			pinctrl-2 = <0x35>;
			broken-cd;
			st,neg-edge;
			bus-width = <0x4>;
			vmmc-supply = <0x1c>;
		};

		usb-otg@49000000 {
			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
			reg = <0x49000000 0x10000>;
			clocks = <0x4 0xa6>;
			clock-names = "otg";
			resets = <0x4 0x4cc8>;
			reset-names = "dwc2";
			interrupts = <0x0 0x62 0x4>;
			g-rx-fifo-size = <0x100>;
			g-np-tx-fifo-size = <0x20>;
			g-tx-fifo-size = <0x80 0x80 0x40 0x40 0x40 0x40 0x20 0x20>;
			dr_mode = "peripheral";
			usb33d-supply = <0x36>;
			status = "okay";
			phys = <0x37 0x0>;
			phy-names = "usb2-phy";
		};

		mailbox@4c001000 {
			compatible = "st,stm32mp1-ipcc";
			#mbox-cells = <0x1>;
			reg = <0x4c001000 0x400>;
			st,proc-id = <0x0>;
			interrupts-extended = <0x1 0x0 0x64 0x4 0x1 0x0 0x65 0x4 0x38 0x3d 0x1>;
			interrupt-names = "rx", "tx", "wakeup";
			clocks = <0x4 0x53>;
			wakeup-source;
			status = "okay";
			phandle = <0x58>;
		};

		dcmi@4c006000 {
			compatible = "st,stm32-dcmi";
			reg = <0x4c006000 0x400>;
			interrupts = <0x0 0x4e 0x4>;
			resets = <0x4 0x4d00>;
			clocks = <0x4 0x4d>;
			clock-names = "mclk";
			dmas = <0x5 0x4b 0x400 0xd>;
			dma-names = "tx";
			status = "disabled";
		};

		rcc@50000000 {
			compatible = "st,stm32mp1-rcc", "syscon";
			reg = <0x50000000 0x1000>;
			#clock-cells = <0x1>;
			#reset-cells = <0x1>;
			phandle = <0x4>;
		};

		pwr@50001000 {
			compatible = "st,stm32mp1,pwr-reg";
			reg = <0x50001000 0x10>;
			vdd-supply = <0x30>;
			vdd_3v3_usbfs-supply = <0x39>;

			reg11 {
				regulator-name = "reg11";
				regulator-min-microvolt = <0x10c8e0>;
				regulator-max-microvolt = <0x10c8e0>;
				phandle = <0x48>;
			};

			reg18 {
				regulator-name = "reg18";
				regulator-min-microvolt = <0x1b7740>;
				regulator-max-microvolt = <0x1b7740>;
				phandle = <0x49>;
			};

			usb33 {
				regulator-name = "usb33";
				regulator-min-microvolt = <0x325aa0>;
				regulator-max-microvolt = <0x325aa0>;
				phandle = <0x36>;
			};
		};

		interrupt-controller@5000d000 {
			compatible = "st,stm32mp1-exti", "syscon";
			interrupt-controller;
			#interrupt-cells = <0x2>;
			reg = <0x5000d000 0x400>;
			phandle = <0x38>;
		};

		syscon@50020000 {
			compatible = "st,stm32mp157-syscfg", "syscon";
			reg = <0x50020000 0x400>;
			clocks = <0x4 0x33>;
			phandle = <0x3>;
		};

		timer@50021000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-lptimer";
			reg = <0x50021000 0x400>;
			clocks = <0x4 0x90>;
			clock-names = "mux";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm-lp";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			trigger@1 {
				compatible = "st,stm32-lptimer-trigger";
				reg = <0x1>;
				status = "disabled";
			};

			counter {
				compatible = "st,stm32-lptimer-counter";
				status = "disabled";
			};
		};

		timer@50022000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32-lptimer";
			reg = <0x50022000 0x400>;
			clocks = <0x4 0x91>;
			clock-names = "mux";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm-lp";
				#pwm-cells = <0x3>;
				status = "disabled";
			};

			trigger@2 {
				compatible = "st,stm32-lptimer-trigger";
				reg = <0x2>;
				status = "disabled";
			};
		};

		timer@50023000 {
			compatible = "st,stm32-lptimer";
			reg = <0x50023000 0x400>;
			clocks = <0x4 0x92>;
			clock-names = "mux";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm-lp";
				#pwm-cells = <0x3>;
				status = "disabled";
			};
		};

		timer@50024000 {
			compatible = "st,stm32-lptimer";
			reg = <0x50024000 0x400>;
			clocks = <0x4 0x93>;
			clock-names = "mux";
			status = "disabled";

			pwm {
				compatible = "st,stm32-pwm-lp";
				#pwm-cells = <0x3>;
				status = "disabled";
			};
		};

		vrefbuf@50025000 {
			compatible = "st,stm32-vrefbuf";
			reg = <0x50025000 0x8>;
			regulator-min-microvolt = <0x2625a0>;
			regulator-max-microvolt = <0x2625a0>;
			clocks = <0x4 0x34>;
			status = "okay";
			vdda-supply = <0x30>;
			phandle = <0x31>;
		};

		sai@50027000 {
			compatible = "st,stm32h7-sai";
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			ranges = <0x0 0x50027000 0x400>;
			reg = <0x50027000 0x4 0x500273f0 0x10>;
			interrupts = <0x0 0x92 0x4>;
			resets = <0x4 0x4c88>;
			status = "disabled";

			audio-controller@50027004 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-a";
				reg = <0x4 0x1c>;
				clocks = <0x4 0xa1>;
				clock-names = "sai_ck";
				dmas = <0x5 0x63 0x400 0x1>;
				status = "disabled";
			};

			audio-controller@50027024 {
				#sound-dai-cells = <0x0>;
				compatible = "st,stm32-sai-sub-b";
				reg = <0x24 0x1c>;
				clocks = <0x4 0xa1>;
				clock-names = "sai_ck";
				dmas = <0x5 0x64 0x400 0x1>;
				status = "disabled";
			};
		};

		thermal@50028000 {
			compatible = "st,stm32-thermal";
			reg = <0x50028000 0x100>;
			interrupts = <0x0 0x93 0x4>;
			clocks = <0x4 0x35>;
			clock-names = "pclk";
			#thermal-sensor-cells = <0x0>;
			status = "disabled";
			phandle = <0x2>;
		};

		hash@54002000 {
			compatible = "st,stm32f756-hash";
			reg = <0x54002000 0x400>;
			interrupts = <0x0 0x50 0x4>;
			clocks = <0x4 0x61>;
			resets = <0x4 0xc85>;
			dmas = <0x3a 0x1f 0x10 0x1000a02 0x0 0x0>;
			dma-names = "in";
			dma-maxburst = <0x2>;
			status = "disabled";
		};

		rng@54003000 {
			compatible = "st,stm32-rng";
			reg = <0x54003000 0x400>;
			clocks = <0x4 0x7c>;
			resets = <0x4 0xc86>;
			status = "okay";
		};

		dma-controller@58000000 {
			compatible = "st,stm32h7-mdma";
			reg = <0x58000000 0x1000>;
			interrupts = <0x0 0x7a 0x4>;
			clocks = <0x4 0x64>;
			resets = <0x4 0xd00>;
			#dma-cells = <0x5>;
			dma-channels = <0x20>;
			dma-requests = <0x30>;
			phandle = <0x3a>;
		};

		nand-controller@58002000 {
			compatible = "st,stm32mp15-fmc2";
			reg = <0x58002000 0x1000 0x80000000 0x1000 0x88010000 0x1000 0x88020000 0x1000 0x81000000 0x1000 0x89010000 0x1000 0x89020000 0x1000>;
			interrupts = <0x0 0x30 0x4>;
			dmas = <0x3a 0x14 0x10 0x12000a02 0x0 0x0 0x3a 0x14 0x10 0x12000a08 0x0 0x0 0x3a 0x15 0x10 0x12000a0a 0x0 0x0>;
			dma-names = "tx", "rx", "ecc";
			clocks = <0x4 0x79>;
			resets = <0x4 0xccc>;
			status = "disabled";
		};

		spi@58003000 {
			compatible = "st,stm32f469-qspi";
			reg = <0x58003000 0x1000 0x70000000 0x10000000>;
			reg-names = "qspi", "qspi_mm";
			interrupts = <0x0 0x5c 0x4>;
			dmas = <0x3a 0x16 0x10 0x100002 0x0 0x0 0x3a 0x16 0x10 0x100008 0x0 0x0>;
			dma-names = "tx", "rx";
			clocks = <0x4 0x7a>;
			resets = <0x4 0xcce>;
			status = "disabled";
		};

		sdmmc@58005000 {
			compatible = "arm,pl18x", "arm,primecell";
			arm,primecell-periphid = <0x10153180>;
			reg = <0x58005000 0x1000>;
			interrupts = <0x0 0x31 0x4>;
			interrupt-names = "cmd_irq";
			clocks = <0x4 0x76>;
			clock-names = "apb_pclk";
			resets = <0x4 0xcd0>;
			cap-sd-highspeed;
			cap-mmc-highspeed;
			max-frequency = <0x7270e00>;
			status = "okay";
			pinctrl-names = "default", "opendrain", "sleep";
			pinctrl-0 = <0x3b>;
			pinctrl-1 = <0x3c>;
			pinctrl-2 = <0x3d>;
			cd-gpios = <0x3e 0x7 0x11>;
			disable-wp;
			st,neg-edge;
			bus-width = <0x4>;
			vmmc-supply = <0x1c>;
		};

		sdmmc@58007000 {
			compatible = "arm,pl18x", "arm,primecell";
			arm,primecell-periphid = <0x10153180>;
			reg = <0x58007000 0x1000>;
			interrupts = <0x0 0x7c 0x4>;
			interrupt-names = "cmd_irq";
			clocks = <0x4 0x77>;
			clock-names = "apb_pclk";
			resets = <0x4 0xcd1>;
			cap-sd-highspeed;
			cap-mmc-highspeed;
			max-frequency = <0x7270e00>;
			status = "disabled";
		};

		crc@58009000 {
			compatible = "st,stm32f7-crc";
			reg = <0x58009000 0x400>;
			clocks = <0x4 0x6e>;
			status = "disabled";
		};

		stmmac-axi-config {
			snps,wr_osr_lmt = <0x7>;
			snps,rd_osr_lmt = <0x7>;
			snps,blen = <0x0 0x0 0x0 0x0 0x10 0x8 0x4>;
			phandle = <0x3f>;
		};

		ethernet@5800a000 {
			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
			reg = <0x5800a000 0x2000>;
			reg-names = "stmmaceth";
			interrupts-extended = <0x1 0x0 0x3d 0x4>;
			interrupt-names = "macirq";
			clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx", "eth-ck", "ethstp";
			clocks = <0x4 0x69 0x4 0x67 0x4 0x68 0x4 0x7b 0x4 0x70>;
			st,syscon = <0x3 0x4>;
			snps,mixed-burst;
			snps,pbl = <0x2>;
			snps,en-tx-lpi-clockgating;
			snps,axi-config = <0x3f>;
			snps,tso;
			status = "okay";
			pinctrl-0 = <0x40>;
			pinctrl-1 = <0x41>;
			pinctrl-names = "default", "sleep";
			phy-mode = "rgmii-id";
			max-speed = <0x3e8>;
			phy-handle = <0x42>;

			mdio0 {
				#address-cells = <0x1>;
				#size-cells = <0x0>;
				compatible = "snps,dwmac-mdio";

				ethernet-phy@0 {
					reg = <0x0>;
					phandle = <0x42>;
				};
			};
		};

		usbh-ohci@5800c000 {
			compatible = "generic-ohci";
			reg = <0x5800c000 0x1000>;
			clocks = <0x4 0x6f>;
			resets = <0x4 0xcd8>;
			interrupts = <0x0 0x4a 0x4>;
			status = "disabled";
			phandle = <0x43>;
		};

		usbh-ehci@5800d000 {
			compatible = "generic-ehci";
			reg = <0x5800d000 0x1000>;
			clocks = <0x4 0x6f>;
			resets = <0x4 0xcd8>;
			interrupts = <0x0 0x4b 0x4>;
			companion = <0x43>;
			status = "okay";
			phys = <0x44>;
		};

		display-controller@5a001000 {
			compatible = "st,stm32-ltdc";
			reg = <0x5a001000 0x400>;
			interrupts = <0x0 0x58 0x4 0x0 0x59 0x4>;
			clocks = <0x4 0xa7>;
			clock-names = "lcd";
			resets = <0x4 0xc00>;
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <0x45>;
			pinctrl-1 = <0x46>;

			port {
				#address-cells = <0x1>;
				#size-cells = <0x0>;

				endpoint@0 {
					reg = <0x0>;
					remote-endpoint = <0x47>;
					phandle = <0x1a>;
				};
			};
		};

		watchdog@5a002000 {
			compatible = "st,stm32mp1-iwdg";
			reg = <0x5a002000 0x400>;
			clocks = <0x4 0x3a 0x4 0x2>;
			clock-names = "pclk", "lsi";
			status = "okay";
			timeout-sec = <0x20>;
		};

		usbphyc@5a006000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32mp1-usbphyc";
			reg = <0x5a006000 0x1000>;
			clocks = <0x4 0x7f>;
			resets = <0x4 0xc10>;
			status = "okay";

			usb-phy@0 {
				#phy-cells = <0x0>;
				reg = <0x0>;
				phy-supply = <0x39>;
				vdda1v1-supply = <0x48>;
				vdda1v8-supply = <0x49>;
				phandle = <0x44>;
			};

			usb-phy@1 {
				#phy-cells = <0x1>;
				reg = <0x1>;
				phy-supply = <0x39>;
				vdda1v1-supply = <0x48>;
				vdda1v8-supply = <0x49>;
				phandle = <0x37>;
			};
		};

		serial@5c000000 {
			compatible = "st,stm32h7-uart";
			reg = <0x5c000000 0x400>;
			interrupts = <0x0 0x25 0x4>;
			clocks = <0x4 0x94>;
			status = "disabled";
		};

		spi@5c001000 {
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			compatible = "st,stm32h7-spi";
			reg = <0x5c001000 0x400>;
			interrupts = <0x0 0x56 0x4>;
			clocks = <0x4 0x87>;
			resets = <0x4 0xc40>;
			dmas = <0x3a 0x22 0x0 0x40008 0x0 0x0 0x3a 0x23 0x0 0x40002 0x0 0x0>;
			dma-names = "rx", "tx";
			status = "disabled";
		};

		i2c@5c002000 {
			compatible = "st,stm32f7-i2c";
			reg = <0x5c002000 0x400>;
			interrupt-names = "event", "error";
			interrupts = <0x0 0x5f 0x4 0x0 0x60 0x4>;
			clocks = <0x4 0x8c>;
			resets = <0x4 0xc42>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			wakeup-source;
			status = "okay";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <0x4a>;
			pinctrl-1 = <0x4b>;
			i2c-scl-rising-time-ns = <0xb9>;
			i2c-scl-falling-time-ns = <0x14>;
			clock-frequency = <0x61a80>;

			stpmic@33 {
				compatible = "st,stpmic1";
				reg = <0x33>;
				interrupts-extended = <0x18 0x0 0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				status = "okay";

				regulators {
					compatible = "st,stpmic1-regulators";
					ldo1-supply = <0x1c>;
					ldo3-supply = <0x4c>;
					ldo6-supply = <0x1c>;
					pwr_sw1-supply = <0x4d>;
					pwr_sw2-supply = <0x4d>;

					buck1 {
						regulator-name = "vddcore";
						regulator-min-microvolt = <0x124f80>;
						regulator-max-microvolt = <0x149970>;
						regulator-always-on;
						regulator-initial-mode = <0x0>;
						regulator-over-current-protection;
					};

					buck2 {
						regulator-name = "vdd_ddr";
						regulator-min-microvolt = <0x149970>;
						regulator-max-microvolt = <0x149970>;
						regulator-always-on;
						regulator-initial-mode = <0x0>;
						regulator-over-current-protection;
						phandle = <0x4c>;
					};

					buck3 {
						regulator-name = "vdd";
						regulator-min-microvolt = <0x325aa0>;
						regulator-max-microvolt = <0x325aa0>;
						regulator-always-on;
						st,mask-reset;
						regulator-initial-mode = <0x0>;
						regulator-over-current-protection;
						phandle = <0x30>;
					};

					buck4 {
						regulator-name = "v3v3";
						regulator-min-microvolt = <0x325aa0>;
						regulator-max-microvolt = <0x325aa0>;
						regulator-always-on;
						regulator-over-current-protection;
						regulator-initial-mode = <0x0>;
						phandle = <0x1c>;
					};

					ldo1 {
						regulator-name = "v1v8_audio";
						regulator-min-microvolt = <0x1b7740>;
						regulator-max-microvolt = <0x1b7740>;
						regulator-always-on;
						interrupts = <0x10 0x0>;
						phandle = <0x1d>;
					};

					ldo2 {
						regulator-name = "v3v3_hdmi";
						regulator-min-microvolt = <0x325aa0>;
						regulator-max-microvolt = <0x325aa0>;
						regulator-always-on;
						interrupts = <0x11 0x0>;
						phandle = <0x16>;
					};

					ldo3 {
						regulator-name = "vtt_ddr";
						regulator-min-microvolt = <0x7a120>;
						regulator-max-microvolt = <0xb71b0>;
						regulator-always-on;
						regulator-over-current-protection;
					};

					ldo4 {
						regulator-name = "vdd_usb";
						interrupts = <0x13 0x0>;
						phandle = <0x39>;
					};

					ldo5 {
						regulator-name = "vdda";
						regulator-min-microvolt = <0x2c4020>;
						regulator-max-microvolt = <0x2c4020>;
						interrupts = <0x14 0x0>;
						regulator-boot-on;
					};

					ldo6 {
						regulator-name = "v1v2_hdmi";
						regulator-min-microvolt = <0x124f80>;
						regulator-max-microvolt = <0x124f80>;
						regulator-always-on;
						interrupts = <0x15 0x0>;
						phandle = <0x17>;
					};

					vref_ddr {
						regulator-name = "vref_ddr";
						regulator-always-on;
					};

					boost {
						regulator-name = "bst_out";
						interrupts = <0xe 0x0>;
						phandle = <0x4d>;
					};

					pwr_sw1 {
						regulator-name = "vbus_otg";
						interrupts = <0xc 0x0>;
					};

					pwr_sw2 {
						regulator-name = "vbus_sw";
						interrupts = <0xd 0x0>;
						regulator-active-discharge = <0x1>;
					};
				};

				onkey {
					compatible = "st,stpmic1-onkey";
					interrupts = <0x0 0x0 0x1 0x0>;
					interrupt-names = "onkey-falling", "onkey-rising";
					power-off-time-sec = <0xa>;
					status = "okay";
				};

				watchdog {
					compatible = "st,stpmic1-wdt";
					status = "disabled";
				};
			};
		};

		rtc@5c004000 {
			compatible = "st,stm32mp1-rtc";
			reg = <0x5c004000 0x400>;
			clocks = <0x4 0x41 0x4 0xc0>;
			clock-names = "pclk", "rtc_ck";
			interrupts = <0x0 0x3 0x4>;
			status = "okay";
		};

		efuse@5c005000 {
			compatible = "st,stm32mp15-bsec";
			reg = <0x5c005000 0x400>;
			#address-cells = <0x1>;
			#size-cells = <0x1>;

			calib@5c {
				reg = <0x5c 0x2>;
			};

			calib@5e {
				reg = <0x5e 0x2>;
			};
		};

		i2c@5c009000 {
			compatible = "st,stm32f7-i2c";
			reg = <0x5c009000 0x400>;
			interrupt-names = "event", "error";
			interrupts = <0x0 0x87 0x4 0x0 0x88 0x4>;
			clocks = <0x4 0x8e>;
			resets = <0x4 0xc43>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			wakeup-source;
			status = "disabled";
		};

		pin-controller@50002000 {
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			compatible = "st,stm32mp157-pinctrl";
			ranges = <0x0 0x50002000 0xa400>;
			interrupt-parent = <0x38>;
			st,syscfg = <0x38 0x60 0xff>;
			pins-are-numbered;
			st,package = <0x4>;
			phandle = <0x4e>;

			gpio@50002000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x0 0x400>;
				clocks = <0x4 0x54>;
				st,bank-name = "GPIOA";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x0 0x10>;
				phandle = <0x18>;
			};

			gpio@50003000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x1000 0x400>;
				clocks = <0x4 0x55>;
				st,bank-name = "GPIOB";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x10 0x10>;
				phandle = <0x3e>;
			};

			gpio@50004000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x2000 0x400>;
				clocks = <0x4 0x56>;
				st,bank-name = "GPIOC";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x20 0x10>;
			};

			gpio@50005000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x3000 0x400>;
				clocks = <0x4 0x57>;
				st,bank-name = "GPIOD";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x30 0x10>;
				phandle = <0x59>;
			};

			gpio@50006000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x4000 0x400>;
				clocks = <0x4 0x58>;
				st,bank-name = "GPIOE";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x40 0x10>;
			};

			gpio@50007000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x5000 0x400>;
				clocks = <0x4 0x59>;
				st,bank-name = "GPIOF";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x50 0x10>;
			};

			gpio@50008000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x6000 0x400>;
				clocks = <0x4 0x5a>;
				st,bank-name = "GPIOG";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x60 0x10>;
				phandle = <0x19>;
			};

			gpio@50009000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x7000 0x400>;
				clocks = <0x4 0x5b>;
				st,bank-name = "GPIOH";
				status = "okay";
				ngpios = <0x10>;
				gpio-ranges = <0x4e 0x0 0x70 0x10>;
			};

			gpio@5000a000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x8000 0x400>;
				clocks = <0x4 0x5c>;
				st,bank-name = "GPIOI";
				status = "okay";
				ngpios = <0xc>;
				gpio-ranges = <0x4e 0x0 0x80 0xc>;
			};

			gpio@5000b000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x9000 0x400>;
				clocks = <0x4 0x5d>;
				st,bank-name = "GPIOJ";
				status = "disabled";
			};

			gpio@5000c000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0xa000 0x400>;
				clocks = <0x4 0x5e>;
				st,bank-name = "GPIOK";
				status = "disabled";
			};

			adc1-in6 {

				pins {
					pinmux = <0x5c11>;
				};
			};

			adc12-ain-0 {
				phandle = <0x2e>;

				pins {
					pinmux = <0x2311 0x5c11 0x5d11 0x5e11>;
				};
			};

			adc12-usb-cc-pins-0 {
				phandle = <0x2f>;

				pins {
					pinmux = <0x411 0x511>;
				};
			};

			cec-0 {

				pins {
					pinmux = <0xf05>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			cec-sleep-0 {

				pins {
					pinmux = <0xf11>;
				};
			};

			cec-1 {
				phandle = <0x22>;

				pins {
					pinmux = <0x1606>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			cec-sleep-1 {
				phandle = <0x23>;

				pins {
					pinmux = <0x1611>;
				};
			};

			dac-ch1 {

				pins {
					pinmux = <0x411>;
				};
			};

			dac-ch2 {

				pins {
					pinmux = <0x511>;
				};
			};

			dcmi-0 {

				pins {
					pinmux = <0x780e 0x170e 0x60e 0x790e 0x7a0e 0x7b0e 0x7c0e 0x7e0e 0x840e 0x180e 0x460e 0x810e 0x770e 0x830e 0x7f0e>;
					bias-disable;
				};
			};

			dcmi-sleep-0 {

				pins {
					pinmux = <0x7811 0x1711 0x611 0x7911 0x7a11 0x7b11 0x7c11 0x7e11 0x8411 0x1811 0x4611 0x8111 0x7711 0x8311 0x7f11>;
				};
			};

			rgmii-0 {
				phandle = <0x40>;

				pins1 {
					pinmux = <0x650c 0x640c 0x6d0c 0x6e0c 0x220c 0x420c 0x1b0c 0x210c>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x2>;
				};

				pins2 {
					pinmux = <0x20c>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x0>;
				};

				pins3 {
					pinmux = <0x240c 0x250c 0x100c 0x110c 0x10c 0x70c>;
					bias-disable;
				};
			};

			rgmii-sleep-0 {
				phandle = <0x41>;

				pins1 {
					pinmux = <0x6511 0x6411 0x6d11 0x6e11 0x2211 0x4211 0x1b11 0x211 0x2111 0x2411 0x2511 0x1011 0x1111 0x111 0x711>;
				};
			};

			rmii-0 {

				pins1 {
					pinmux = <0x6d0c 0x6e0c 0x1b0c 0x101 0x20c 0x210c>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x2>;
				};

				pins2 {
					pinmux = <0x240c 0x250c 0x70c>;
					bias-disable;
				};
			};

			rmii-sleep-0 {

				pins1 {
					pinmux = <0x6d11 0x6e11 0x1b11 0x211 0x2111 0x2411 0x2511 0x111 0x711>;
				};
			};

			fmc-0 {

				pins1 {
					pinmux = <0x340d 0x350d 0x3b0d 0x3c0d 0x3e0d 0x3f0d 0x300d 0x310d 0x470d 0x480d 0x490d 0x4a0d 0x690d>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x1>;
				};

				pins2 {
					pinmux = <0x360d>;
					bias-pull-up;
				};
			};

			fmc-sleep-0 {

				pins {
					pinmux = <0x3411 0x3511 0x3b11 0x3c11 0x3e11 0x3f11 0x3011 0x3111 0x4711 0x4811 0x4911 0x4a11 0x3611 0x6911>;
				};
			};

			i2c1-0 {
				phandle = <0x14>;

				pins {
					pinmux = <0x3c06 0x5f06>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c1-1 {
				phandle = <0x15>;

				pins {
					pinmux = <0x3c11 0x5f11>;
				};
			};

			i2c1-2 {

				pins {
					pinmux = <0x5e06 0x5f06>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c1-3 {

				pins {
					pinmux = <0x5e11 0x5f11>;
				};
			};

			i2c2-0 {

				pins {
					pinmux = <0x7405 0x7505>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c2-1 {

				pins {
					pinmux = <0x7411 0x7511>;
				};
			};

			i2c2-2 {

				pins {
					pinmux = <0x7505>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c2-3 {

				pins {
					pinmux = <0x7511>;
				};
			};

			i2c5-0 {

				pins {
					pinmux = <0xb05 0xc05>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c5-1 {

				pins {
					pinmux = <0xb11 0xc11>;
				};
			};

			i2s2-0 {
				phandle = <0x10>;

				pins {
					pinmux = <0x8306 0x1906 0x906>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-disable;
				};
			};

			i2s2-1 {
				phandle = <0x11>;

				pins {
					pinmux = <0x8311 0x1911 0x911>;
				};
			};

			ltdc-a-0 {
				phandle = <0x45>;

				pins {
					pinmux = <0x670f 0x8a0f 0x890f 0x5a0f 0x720f 0x730f 0x780f 0x790f 0x7a0f 0x200f 0x7c0f 0x4f0f 0x450f 0x460f 0x7d0f 0x7e0f 0x7f0f 0x800f 0x810f 0x820f 0x390f 0x6c0f 0x6a0f 0x3a0f 0x840f 0x30f 0x180f 0x380f>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x1>;
				};
			};

			ltdc-a-1 {
				phandle = <0x46>;

				pins {
					pinmux = <0x6711 0x8a11 0x8911 0x5a11 0x7211 0x7311 0x7811 0x7911 0x7a11 0x2011 0x7c11 0x4f11 0x4511 0x4611 0x7d11 0x7e11 0x7f11 0x8011 0x8111 0x8211 0x3911 0x6c11 0x6a11 0x3a11 0x8411 0x311 0x1811 0x3811>;
				};
			};

			ltdc-b-0 {

				pins {
					pinmux = <0x8e0f 0x8c0f 0x8d0f 0xa70f 0x8f0f 0x900f 0x910f 0x920f 0x930f 0x940f 0x950f 0x960f 0x970f 0x980f 0x990f 0x9a0f 0x9b0f 0xa00f 0xa10f 0xa20f 0x9c0f 0x9d0f 0x9e0f 0x9f0f 0xa30f 0xa40f 0xa50f 0xa60f>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x1>;
				};
			};

			ltdc-b-1 {

				pins {
					pinmux = <0x8e11 0x8c11 0x8d11 0xa711 0x8f11 0x9011 0x9111 0x9211 0x9311 0x9411 0x9511 0x9611 0x9711 0x9811 0x9911 0x9a11 0x9b11 0xa011 0xa111 0xa211 0x9c11 0x9d11 0x9e11 0x9f11 0xa311 0xa411 0xa511 0xa611>;
				};
			};

			m-can1-0 {

				pins1 {
					pinmux = <0x7d0a>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-disable;
				};

				pins2 {
					pinmux = <0x890a>;
					bias-disable;
				};
			};

			m_can1-sleep-0 {

				pins {
					pinmux = <0x7d11 0x8911>;
				};
			};

			pwm1-0 {
				phandle = <0x24>;

				pins {
					pinmux = <0x4902 0x4b02 0x4e02>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm1-sleep-0 {
				phandle = <0x25>;

				pins {
					pinmux = <0x4911 0x4b11 0x4e11>;
				};
			};

			pwm2-0 {

				pins {
					pinmux = <0x302>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm2-sleep-0 {

				pins {
					pinmux = <0x311>;
				};
			};

			pwm3-0 {
				phandle = <0x6>;

				pins {
					pinmux = <0x2703>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm3-sleep-0 {
				phandle = <0x7>;

				pins {
					pinmux = <0x2711>;
				};
			};

			pwm4-0 {
				phandle = <0x8>;

				pins {
					pinmux = <0x3e03 0x3f03>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm4-sleep-0 {
				phandle = <0xa>;

				pins {
					pinmux = <0x3e11 0x3f11>;
				};
			};

			pwm4-1 {
				phandle = <0x9>;

				pins {
					pinmux = <0x3d03>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm4-sleep-1 {
				phandle = <0xb>;

				pins {
					pinmux = <0x3d11>;
				};
			};

			pwm5-0 {
				phandle = <0xc>;

				pins {
					pinmux = <0x7b03>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm5-sleep-0 {
				phandle = <0xd>;

				pins {
					pinmux = <0x7b11>;
				};
			};

			pwm8-0 {

				pins {
					pinmux = <0x8204>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm8-sleep-0 {

				pins {
					pinmux = <0x8211>;
				};
			};

			pwm12-0 {
				phandle = <0xe>;

				pins {
					pinmux = <0x7603>;
					bias-pull-down;
					drive-push-pull;
					slew-rate = <0x0>;
				};
			};

			pwm12-sleep-0 {
				phandle = <0xf>;

				pins {
					pinmux = <0x7611>;
				};
			};

			qspi-clk-0 {

				pins {
					pinmux = <0x5a0a>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x3>;
				};
			};

			qspi-clk-sleep-0 {

				pins {
					pinmux = <0x5a11>;
				};
			};

			qspi-bk1-0 {

				pins1 {
					pinmux = <0x580b 0x590b 0x570a 0x560a>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x1>;
				};

				pins2 {
					pinmux = <0x160b>;
					bias-pull-up;
					drive-push-pull;
					slew-rate = <0x1>;
				};
			};

			qspi-bk1-sleep-0 {

				pins {
					pinmux = <0x5811 0x5911 0x5711 0x5611 0x1611>;
				};
			};

			qspi-bk2-0 {

				pins1 {
					pinmux = <0x720a 0x730a 0x6a0c 0x670c>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x1>;
				};

				pins2 {
					pinmux = <0x200b>;
					bias-pull-up;
					drive-push-pull;
					slew-rate = <0x1>;
				};
			};

			qspi-bk2-sleep-0 {

				pins {
					pinmux = <0x7211 0x7311 0x6a11 0x6711 0x2011>;
				};
			};

			sai2a-0 {
				phandle = <0x26>;

				pins {
					pinmux = <0x850b 0x860b 0x870b 0x400b>;
					slew-rate = <0x0>;
					drive-push-pull;
					bias-disable;
				};
			};

			sai2a-1 {
				phandle = <0x28>;

				pins {
					pinmux = <0x8511 0x8611 0x8711 0x4011>;
				};
			};

			sai2a-2 {

				pins1 {
					pinmux = <0x860b 0x870b 0x3d0b>;
					slew-rate = <0x0>;
					drive-push-pull;
					bias-disable;
				};
			};

			sai2a-sleep-3 {

				pins {
					pinmux = <0x8611 0x8711 0x3d11>;
				};
			};

			sai2b-0 {

				pins1 {
					pinmux = <0x4c0b 0x4d0b 0x4e0b>;
					slew-rate = <0x0>;
					drive-push-pull;
					bias-disable;
				};

				pins2 {
					pinmux = <0x5b0b>;
					bias-disable;
				};
			};

			sai2b-1 {

				pins {
					pinmux = <0x5b11 0x4c11 0x4d11 0x4e11>;
				};
			};

			sai2b-2 {
				phandle = <0x27>;

				pins {
					pinmux = <0x5b0b>;
					bias-disable;
				};
			};

			sai2b-3 {
				phandle = <0x29>;

				pins {
					pinmux = <0x5b11>;
				};
			};

			sai4a-0 {

				pins {
					pinmux = <0x150b>;
					slew-rate = <0x0>;
					drive-push-pull;
					bias-disable;
				};
			};

			sai4a-1 {

				pins {
					pinmux = <0x1511>;
				};
			};

			sdmmc1-b4-0 {
				phandle = <0x3b>;

				pins1 {
					pinmux = <0x280d 0x290d 0x2a0d 0x2b0d 0x320d>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-disable;
				};

				pins2 {
					pinmux = <0x2c0d>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-disable;
				};
			};

			sdmmc1-b4-od-0 {
				phandle = <0x3c>;

				pins1 {
					pinmux = <0x280d 0x290d 0x2a0d 0x2b0d>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-disable;
				};

				pins2 {
					pinmux = <0x2c0d>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-disable;
				};

				pins3 {
					pinmux = <0x320d>;
					slew-rate = <0x1>;
					drive-open-drain;
					bias-disable;
				};
			};

			sdmmc1-b4-sleep-0 {
				phandle = <0x3d>;

				pins {
					pinmux = <0x2811 0x2911 0x2a11 0x2b11 0x2c11 0x3211>;
				};
			};

			sdmmc1-dir-0 {

				pins1 {
					pinmux = <0x520c 0x2709 0x190c>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-pull-up;
				};

				pins2 {
					pinmux = <0x4409>;
					bias-pull-up;
				};
			};

			sdmmc1-dir-sleep-0 {

				pins {
					pinmux = <0x5211 0x2711 0x1911 0x4411>;
				};
			};

			sdmmc2-b4-0 {

				pins1 {
					pinmux = <0x1e0a 0x1f0a 0x130a 0x140a 0x660b>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-pull-up;
				};

				pins2 {
					pinmux = <0x430a>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-pull-up;
				};
			};

			sdmmc2-b4-od-0 {

				pins1 {
					pinmux = <0x1e0a 0x1f0a 0x130a 0x140a>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-pull-up;
				};

				pins2 {
					pinmux = <0x430a>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-pull-up;
				};

				pins3 {
					pinmux = <0x660b>;
					slew-rate = <0x1>;
					drive-open-drain;
					bias-pull-up;
				};
			};

			sdmmc2-b4-sleep-0 {

				pins {
					pinmux = <0x1e11 0x1f11 0x1311 0x1411 0x4311 0x6611>;
				};
			};

			sdmmc2-b4-1 {

				pins1 {
					pinmux = <0x1e0a 0x1f0a 0x130a 0x140a 0x660b>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-disable;
				};

				pins2 {
					pinmux = <0x430a>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-disable;
				};
			};

			sdmmc2-b4-od-1 {

				pins1 {
					pinmux = <0x1e0a 0x1f0a 0x130a 0x140a>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-disable;
				};

				pins2 {
					pinmux = <0x430a>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-disable;
				};

				pins3 {
					pinmux = <0x660b>;
					slew-rate = <0x1>;
					drive-open-drain;
					bias-disable;
				};
			};

			sdmmc2-d47-0 {

				pins {
					pinmux = <0x80a 0x90b 0x450a 0x330a>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-pull-up;
				};
			};

			sdmmc2-d47-sleep-0 {

				pins {
					pinmux = <0x811 0x911 0x4511 0x3311>;
				};
			};

			sdmmc3-b4-0 {
				phandle = <0x33>;

				pins1 {
					pinmux = <0x500a 0x540a 0x550a 0x370b 0x510a>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-pull-up;
				};

				pins2 {
					pinmux = <0x6f0b>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-pull-up;
				};
			};

			sdmmc3-b4-od-0 {
				phandle = <0x34>;

				pins1 {
					pinmux = <0x500a 0x540a 0x550a 0x370b>;
					slew-rate = <0x1>;
					drive-push-pull;
					bias-pull-up;
				};

				pins2 {
					pinmux = <0x6f0b>;
					slew-rate = <0x2>;
					drive-push-pull;
					bias-pull-up;
				};

				pins3 {
					pinmux = <0x510a>;
					slew-rate = <0x1>;
					drive-open-drain;
					bias-pull-up;
				};
			};

			sdmmc3-b4-sleep-0 {
				phandle = <0x35>;

				pins {
					pinmux = <0x5011 0x5411 0x5511 0x3711 0x6f11 0x5111>;
				};
			};

			spdifrx-0 {

				pins {
					pinmux = <0x6c09>;
					bias-disable;
				};
			};

			spdifrx-1 {

				pins {
					pinmux = <0x6c11>;
				};
			};

			usart3-0 {

				pins1 {
					pinmux = <0x1a08>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x0>;
				};

				pins2 {
					pinmux = <0x1c09>;
					bias-disable;
				};
			};

			uart4-0 {
				phandle = <0x13>;

				pins1 {
					pinmux = <0x6b07>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x0>;
				};

				pins2 {
					pinmux = <0x1209>;
					bias-disable;
				};
			};

			uart4-1 {

				pins1 {
					pinmux = <0x3109>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x0>;
				};

				pins2 {
					pinmux = <0x1209>;
					bias-disable;
				};
			};

			uart7-0 {

				pins1 {
					pinmux = <0x4808>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x0>;
				};

				pins2 {
					pinmux = <0x4708 0x4a08 0x4908>;
					bias-disable;
				};
			};

			uart8-0 {

				pins1 {
					pinmux = <0x4109>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x0>;
				};

				pins2 {
					pinmux = <0x4009>;
					bias-disable;
				};
			};

			usbotg-hs-0 {

				pins {
					pinmux = <0xa11>;
				};
			};

			usbotg-fs-dp-dm-0 {

				pins {
					pinmux = <0xb11 0xc11>;
				};
			};
		};

		pin-controller-z@54004000 {
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			compatible = "st,stm32mp157-z-pinctrl";
			ranges = <0x0 0x54004000 0x400>;
			pins-are-numbered;
			interrupt-parent = <0x38>;
			st,syscfg = <0x38 0x60 0xff>;
			st,package = <0x4>;
			phandle = <0x4f>;

			gpio@54004000 {
				gpio-controller;
				#gpio-cells = <0x2>;
				interrupt-controller;
				#interrupt-cells = <0x2>;
				reg = <0x0 0x400>;
				clocks = <0x4 0x5f>;
				st,bank-name = "GPIOZ";
				st,bank-ioport = <0xb>;
				status = "okay";
				ngpios = <0x8>;
				gpio-ranges = <0x4f 0x0 0x190 0x8>;
			};

			i2c2-0 {

				pins {
					pinmux = <0x19004>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c2-1 {

				pins {
					pinmux = <0x19011>;
				};
			};

			i2c4-0 {
				phandle = <0x4a>;

				pins {
					pinmux = <0x19407 0x19507>;
					bias-disable;
					drive-open-drain;
					slew-rate = <0x0>;
				};
			};

			i2c4-1 {
				phandle = <0x4b>;

				pins {
					pinmux = <0x19411 0x19511>;
				};
			};

			spi1-0 {

				pins1 {
					pinmux = <0x19006 0x19206>;
					bias-disable;
					drive-push-pull;
					slew-rate = <0x1>;
				};

				pins2 {
					pinmux = <0x19106>;
					bias-disable;
				};
			};
		};

		can@4400e000 {
			compatible = "bosch,m_can";
			reg = <0x4400e000 0x400 0x44011000 0x1400>;
			reg-names = "m_can", "message_ram";
			interrupts = <0x0 0x13 0x4 0x0 0x15 0x4>;
			interrupt-names = "int0", "int1";
			clocks = <0x4 0x0 0x4 0x9d>;
			clock-names = "hclk", "cclk";
			bosch,mram-cfg = <0x0 0x0 0x0 0x20 0x0 0x0 0x2 0x2>;
			status = "disabled";
		};

		can@4400f000 {
			compatible = "bosch,m_can";
			reg = <0x4400f000 0x400 0x44011000 0x2800>;
			reg-names = "m_can", "message_ram";
			interrupts = <0x0 0x14 0x4 0x0 0x16 0x4>;
			interrupt-names = "int0", "int1";
			clocks = <0x4 0x0 0x4 0x9d>;
			clock-names = "hclk", "cclk";
			bosch,mram-cfg = <0x1400 0x0 0x0 0x20 0x0 0x0 0x2 0x2>;
			status = "disabled";
		};

		gpu@59000000 {
			compatible = "vivante,gc";
			reg = <0x59000000 0x800>;
			interrupts = <0x0 0x6d 0x4>;
			clocks = <0x4 0x65 0x4 0x7e>;
			clock-names = "bus", "core";
			resets = <0x4 0xcc5>;
			status = "okay";
			contiguous-area = <0x50>;
		};

		dsi@5a000000 {
			compatible = "st,stm32-dsi";
			reg = <0x5a000000 0x800>;
			clocks = <0x4 0xa3 0x51 0x4 0xa4>;
			clock-names = "pclk", "ref", "px_clk";
			resets = <0x4 0xc04>;
			reset-names = "apb";
			status = "disabled";
		};
	};

	ahb {
		compatible = "st,mlahb", "simple-bus";
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		ranges;
		dma-ranges = <0x0 0x38000000 0x10000 0x10000000 0x10000000 0x60000 0x30000000 0x30000000 0x60000>;

		m4@10000000 {
			compatible = "st,stm32mp1-m4";
			reg = <0x10000000 0x40000 0x30000000 0x40000 0x38000000 0x10000>;
			resets = <0x4 0x2021>;
			st,syscfg-holdboot = <0x4 0x10c 0x1>;
			st,syscfg-tz = <0x4 0x0 0x1>;
			status = "okay";
			memory-region = <0x52 0x53 0x54 0x55 0x56 0x57>;
			mboxes = <0x58 0x0 0x58 0x1 0x58 0x2>;
			mbox-names = "vq0", "vq1", "shutdown";
			interrupt-parent = <0x38>;
			interrupts = <0x44 0x1>;
		};
	};

	memory@c0000000 {
		device_type = "memory";
		reg = <0xc0000000 0x20000000>;
	};

	reserved-memory {
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		ranges;

		mcuram2@10000000 {
			compatible = "shared-dma-pool";
			reg = <0x10000000 0x40000>;
			no-map;
			phandle = <0x54>;
		};

		vdev0vring0@10040000 {
			compatible = "shared-dma-pool";
			reg = <0x10040000 0x1000>;
			no-map;
			phandle = <0x55>;
		};

		vdev0vring1@10041000 {
			compatible = "shared-dma-pool";
			reg = <0x10041000 0x1000>;
			no-map;
			phandle = <0x56>;
		};

		vdev0buffer@10042000 {
			compatible = "shared-dma-pool";
			reg = <0x10042000 0x4000>;
			no-map;
			phandle = <0x57>;
		};

		mcuram@30000000 {
			compatible = "shared-dma-pool";
			reg = <0x30000000 0x40000>;
			no-map;
			phandle = <0x53>;
		};

		retram@38000000 {
			compatible = "shared-dma-pool";
			reg = <0x38000000 0x10000>;
			no-map;
			phandle = <0x52>;
		};

		gpu@d4000000 {
			reg = <0xd4000000 0x4000000>;
			no-map;
			phandle = <0x50>;
		};
	};

	led {
		compatible = "gpio-leds";

		blue {
			label = "heartbeat";
			gpios = <0x59 0xb 0x0>;
			linux,default-trigger = "heartbeat";
			default-state = "off";
		};
	};

	sound {
		compatible = "audio-graph-card";
		label = "STM32MP1-DK";
		routing = "Playback", "MCLK", "Capture", "MCLK", "MICL", "Mic Bias";
		dais = <0x5a 0x5b 0x5c>;
		status = "okay";
	};

	aliases {
		ethernet0 = "/soc/ethernet@5800a000";
		serial0 = "/soc/serial@40010000";
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};
};