Resolved! ST87M01 - LTE-M Support
Hi, I have been looking at this newer ST87M01 as of here :- https://www.st.com/resource/en/datasheet/st87m01.pdf and wondered does it support LTE-M or only NB-IOT? Thanks!
Interface and connectivity ICs
Ask questions and find answers on connectivity ICs, focusing on protocols and I2C challenges on STM32 Nucleo boards and BlueNRG products.
Forum Posts
L9780 - SPI communication issue
All,I'm working on the basics of getting the SPI communication set up for the L9780 IC and am running into some issues, so I'd appreciate some feedback or a double-check. It appears so far that I'm able to send a command via the control word and succ...
Can ST67W be directly controlled from an Ethernet Switch?
Hi STM team, I would like to know if/how I can simply connect e.g. the ST67W611M1 or another WiFi module to a switch IC, e.g. the KSZ8795CLXIC, without needing a microcontroller. Or is there a switch IC that can be connected directly to the ST67W611M...
Resolved! Problem with ST67W61 in w61_at_common.c
Greetings,I'm trying to run an application using X-CUBE-ST67W61, but I'm encountering a problem at this line in w61_at_common.c:int32_t W61_AT_ModemInit(W61_Object_t *Obj) { (...) xReturned = xSemaphoreTake(mdm->sem_if_ready, pdMS_TO_TICKS(4000)); (....
Resolved! ST KNX 68R Immunity Test Problem
We are using 2 KNX IC on our project. One of them for communication and some LEDs other one (STKNX) just for driving LEDs not for communication. But of course is directly connected to KNX_BUS line. When we applied Surge test , TVS couldn't protect th...
ST67W611M1 AT+CIPSTART documentation incomplete
The API documentation for the "AT+CIPSTART" command on the ST67W611M1 chip seems to be incomplete. It is missing the parameter lists for UDP and SSL types. https://wiki.st.com/stm32mcu/wiki/Connectivity:ST67W611M_AT_Command#AT-2BCIPSTART The rest of ...
QoS configuration on ST67W
Hi, i have bought a Nucleo-U575ZI-Q coupled with a X-Nucleo-67W61M1 i have upload the exemple ST67W6X_MQTT, after reading the doc i have complete the configuration and i run well. I use it with mosquitto or nanomq brokers (same results) but on both ...
interfacing STEVAL-IOM001V1 with STSW-IOLINKGUI to get reading from SICK DT35 distance sensor.
Im trying to get the reading from distance sensor SICK DT35 through STEVAL-IOM001V1 which uses the L6360 IC via STSW-IOLINKGUI to get the proper reading we need to upload the IODD file of the sensor which I'm not be able to do with the GUI. There's n...
BlueNRG-M2SP – Unable to detect firmware or device via BlueNRG-GUI after flashing DTM project
Hello,I am using a BlueNRG-M2SP module mounted on my own custom PCB. I programmed it using the STSW-BLUENRG1-DK package and flashed the DTM / UART project to check basic functionality and enable advertising.The project runs correctly in Debug mode, r...
Resolved! ST67W611M1 connecting to WiFi AP with password including a comma is not working
Hi !We're testing with the eval-boards NUCLEO-H7S3L8 + X-NUCLEO-67W61M1.The software is the CLI project of the NUCLEO-H7S3L8.At the bottom of this post you will find infos to the software versions.There we're having an issue when we try to connect to...
