Posted on October 31, 2013 at 09:04Hi, I am trying to communicate with MCP4725(12bit DAC) via I2C using STM32F030C8T6. The program gets stuck at one of the status checking part. Can somebody look at my code and see what the problem is?
//Code to Initialize I2C
void InitI2C(void){
//PB8 = SCL1, PB9 = SDA1
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);//I2C1
RCC_I2CCLKConfig(RCC_I2C1CLK_HSI); //I2C
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);//I2C1 GPIO
GPIO_PinAFConfig(GPIOB, GPIO_PinSource8, GPIO_AF_1);
GPIO_PinAFConfig(GPIOB, GPIO_PinSource9, GPIO_AF_1);
GPIO_StructInit(&GPIO_InitStruct);
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_8; //SCL
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStruct.GPIO_OType = GPIO_OType_OD;
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOB, &GPIO_InitStruct);
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_9;
GPIO_Init(GPIOB, &GPIO_InitStruct);
I2C_InitStruct.I2C_Mode = I2C_Mode_I2C;//NOt SMBUS host
I2C_InitStruct.I2C_AnalogFilter = I2C_AnalogFilter_Enable;
I2C_InitStruct.I2C_DigitalFilter = 0x00;
I2C_InitStruct.I2C_OwnAddress1 = 0x00;
I2C_InitStruct.I2C_Ack = I2C_Ack_Enable;
I2C_InitStruct.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
I2C_InitStruct.I2C_Timing = 0x10400CDB;//STM�?� I2C Configuration tool
I2C_Init(I2C1, &I2C_InitStruct);
I2C_Cmd(I2C1, ENABLE);
}
//code to communicate with I2C
void WriteMCP4725(uint16_t data){
uint8_t high_buffer, low_buffer;
if(data > 4095) data = 4095;
high_buffer = (uint8_t)((data>>8) & 0xFF);
low_buffer = (uint8_t)(data & 0xFF);
while(I2C_GetFlagStatus(I2C1, I2C_ISR_BUSY) != RESET);
I2C_TransferHandling(I2C1, 0xC0, 2, I2C_AutoEnd_Mode, I2C_Generate_Start_Write); //Generate Start Condition
while(I2C_GetFlagStatus(I2C1, I2C_ISR_TXIS) == RESET);
I2C_SendData(I2C1, high_buffer);
while(I2C_GetFlagStatus(I2C1, I2C_ISR_TCR) == RESET);
I2C_SendData(I2C1, low_buffer);
while(I2C_GetFlagStatus(I2C1, I2C_ISR_STOPF) == RESET);
I2C_ClearFlag(I2C1, I2C_ICR_STOPCF);
}
am i doing something wrong??
my program doesn't get past the
while(I2C_GetFlagStatus(I2C1, I2C_ISR_TCR) == RESET);
part
Here is the code that works with PIC and CCS compiler
void ext_dac_out(uint8_t dac_type, uint8_t out_sel, uint16_t dac_buffer){
int8 buffer;
int8 high_buffer, low_buffer;
buffer = 0b11000000;//MCP4725
high_buffer = dac_buffer>>8;
low_buffer = dac_buffer;
i2c_start();
i2c_write(buffer);//address byte, write mode
i2c_write(high_buffer);//fast write commands(C2,C1,PD1,PD0,D11-D8)
i2c_write(low_buffer); //write data(D7-D0)
i2c_stop();
Thank you
