could not able to compile code in keil

[SS.Sagar]

Posted on December 16, 2015 at 19:50

Hi,

i m using stm32f103 nucleo board and keil compiler. I downloaded code from keil website for uart. and tried to compile the code but got error as some files are missing. following are the errors.C:\Keil_v5\ARM\PACK\Keil\STM32F1xx_DFP\1.1.0\Device\Include\stm32f10x_lib.h(32): error:  #5: cannot open source input file ''stm32f10x_map.h'': No such file or directoryi have attached the downloaded code from keil side.

[SS.Sagar]

Posted on December 16, 2015 at 19:53

here i have attached the code.

________________ Attachments : stm32_usart_irq.zip : https://st--c.eu10.content.force.com/sfc/dist/version/download/?oid=00Db0000000YtG6&ids=0680X000006I1JL&d=%2Fa%2F0X0000000bl9%2FsztCWQzcUjMd87g62qKP.sU0nMMF5567SjCq9FTZUrc&asPdf=false

[Tesla DeLorean]

Posted on December 16, 2015 at 20:14

Doesn't look to be code designed for uV5, it's far too old.

Have you loaded the legacy packs? Perhaps you can find some newer USART examples in that?

[SS.Sagar]

Posted on December 17, 2015 at 04:08

Can you plz guide me with this.

i m new to stm32 controllers.

[SS.Sagar]

Posted on December 17, 2015 at 17:44

Hi

I followed the following video to get compiler ready to work.https://www.youtube.com/watch?v=w9_8RVFBLIAthen also getting error as files are missing.i configure the keil as shown in video. and use the below code.[code]/************************* * stm32 uart main.c *************************/ #include ''stm32f10x.h'' /* User defined function prototypes */void GPIOA_Init(void);void USART1_Init(void);void led_toggle(void); int main(void){    /* Initialize GPIOA PIN8 */    GPIOA_Init();    /* Initialize USART1 */    USART1_Init();     while(1)    {        /* Do nothing, all happens in ISR */    }}    /*********************************************** * Initialize GPIOA PIN8 as push-pull output ***********************************************/void GPIOA_Init(void){    /* Bit configuration structure for GPIOA PIN8 */    GPIO_InitTypeDef gpioa_init_struct = { GPIO_Pin_8, GPIO_Speed_50MHz,                                            GPIO_Mode_Out_PP };                                                 /* Enable PORT A clock */    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);    /* Initialize GPIOA: 50MHz, PIN8, Push-pull Output */    GPIO_Init(GPIOA, &gpioa_init_struct);            /* Turn off LED to start with */    GPIO_SetBits(GPIOA, GPIO_Pin_8);} /***************************************************** * Initialize USART1: enable interrupt on reception * of a character *****************************************************/void USART1_Init(void){    /* USART configuration structure for USART1 */    USART_InitTypeDef usart1_init_struct;    /* Bit configuration structure for GPIOA PIN9 and PIN10 */    GPIO_InitTypeDef gpioa_init_struct;         /* Enalbe clock for USART1, AFIO and GPIOA */    RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_AFIO |                            RCC_APB2Periph_GPIOA, ENABLE);                                /* GPIOA PIN9 alternative function Tx */    gpioa_init_struct.GPIO_Pin = GPIO_Pin_9;    gpioa_init_struct.GPIO_Speed = GPIO_Speed_50MHz;    gpioa_init_struct.GPIO_Mode = GPIO_Mode_AF_PP;    GPIO_Init(GPIOA, &gpioa_init_struct);    /* GPIOA PIN9 alternative function Rx */    gpioa_init_struct.GPIO_Pin = GPIO_Pin_10;    gpioa_init_struct.GPIO_Speed = GPIO_Speed_50MHz;    gpioa_init_struct.GPIO_Mode = GPIO_Mode_IN_FLOATING;    GPIO_Init(GPIOA, &gpioa_init_struct);     /* Enable USART1 */    USART_Cmd(USART1, ENABLE);      /* Baud rate 9600, 8-bit data, One stop bit     * No parity, Do both Rx and Tx, No HW flow control     */    usart1_init_struct.USART_BaudRate = 9600;       usart1_init_struct.USART_WordLength = USART_WordLength_8b;      usart1_init_struct.USART_StopBits = USART_StopBits_1;       usart1_init_struct.USART_Parity = USART_Parity_No ;    usart1_init_struct.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;    usart1_init_struct.USART_HardwareFlowControl = USART_HardwareFlowControl_None;    /* Configure USART1 */    USART_Init(USART1, &usart1_init_struct);    /* Enable RXNE interrupt */    USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);    /* Enable USART1 global interrupt */    NVIC_EnableIRQ(USART1_IRQn);} /******************************************* * Toggle LED  *******************************************/void led_toggle(void){    /* Read LED output (GPIOA PIN8) status */    uint8_t led_bit = GPIO_ReadOutputDataBit(GPIOA, GPIO_Pin_8);         /* If LED output set, clear it */    if(led_bit == (uint8_t)Bit_SET)    {        GPIO_ResetBits(GPIOA, GPIO_Pin_8);    }    /* If LED output clear, set it */    else    {        GPIO_SetBits(GPIOA, GPIO_Pin_8);    }} /********************************************************** * USART1 interrupt request handler: on reception of a  * character 't', toggle LED and transmit a character 'T' *********************************************************/void USART1_IRQHandler(void){    /* RXNE handler */    if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET)    {        /* If received 't', toggle LED and transmit 'T' */        if((char)USART_ReceiveData(USART1) == 't')        {            led_toggle();            USART_SendData(USART1, 'T');            /* Wait until Tx data register is empty, not really              * required for this example but put in here anyway.             */            /*            while(USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET)            {            }*/        }    }         /* ------------------------------------------------------------ */    /* Other USART1 interrupts handler can go here ...             */} [/code]Plz help me with this.